|
|
 |
One piece design, easily replaceable bolts, connects horizontal or ledger tubes to standards. To be used in every position where the tube it secures comes under load.
Suitable tube wall 3.25mm plus. |
|
|
|
 |
Single unit design, easily replaceable bolts, principally used for bracing and allowing tubes to be connected at any angle. |
|
|
|
|
Single unit design, used for connecting putlogs or transoms to ledger tubes, also extensively for securing guard rails to standards.
|
|
|
|
|
A fitting designed (using specially heat treated pressed steel) for external joining of two tubes end to end.
Recommended for use on ledger and bracing members.
|
|
|
|
|
Specially heat treated, high carbon steel boxes (all rust proofed).
|
|
|
|
|
Used at the base of all standards for the distribution of load, drilled for spiking to sole plates. The locating spigot is a slack enough fit in the tube to allow a degree of angle on uneven ground.
For use with 1 29/32" (48.3mm) tube. 6"x6"x3/16" (152x152x4.76mm).
Weight: 2lbs 12ozs (1.28 kilos)
|
|
|
|
|
One piece design, easily replaceable bolts, connects horizontal or ledger tubes to standards.
|
|
|
|
|
Single Unit design, easily replaceable bolts, principally used for bracing and allowing tubes to be connected at any angle.
|
|
|
|
|
One piece design, connects horizontal or ledger tubes to standards.
|
|
|
|
|
Single unit design, principally used for bracing and allowing tubes to be connected at any angle.
|
|
|
|
|
Similarly used as the Mark II for connecting putlogs or transoms to ledger tubes, this design leaves the putlog/tube completely unobstructed so that the scaffold boards lay flat.
|
|
|
|
|
Designed as Half Double Coupler with flat back for welding.
|
|
|
|
|
One piece design, easily replaceable bolts, connects horizontal or ledger tubes to standards.
|
|
|
|
|
|
Single unit design, easily replaceable bolts, principally used for bracing and allowing tubes to be connected at any angle.
|
|
|
|
|
As its name implies, this is an unriveted half of a Swivel Coupler.
|
|
|
|
|
Designed for joining tubes end to end. It is an internal expanding type, operating against the inner walls of the tubes.
|
|
|
|
|
Designed on the same style as the Half Swivel Coupler, but Body Profiled for welding onto tube.
|
|
|
|
|
A fitting to lap two tubes in parallel, the one bolt fixing firmly securing the tubes together in direct contact.
|
|
|
|
|
Designed for securing timber to tube: is particularly useful in the construction of temporary roofs, sheds, hoardings, grandstands, formwork, etc.
Rafter Couplers are used extensively in both film and television studios for set construction. The vice-like grip of this fitting holds timbers in position without the use of nails or screws.
|
|
|
|
|
The fittings are unique in that they secure tubes of 1.90" (48.3mm) down to 1.50" (38mm) on both sides. Supplied in two types: Right Angle (90°) (rigid). Swivel (360°) (adjustable). Dual Double Coupler - one piece design for connecting horizontal or ledger tubes to standards. Dual Swivel Coupler - one piece design for attaching bracing tubes at any angle.
|
|
|
|
|
Totally drop forged with swivel facility.
|
|
|
|
|
Solid one piece drop forged steel fittings: used for securing 48.3mm (1.90") OD tubes to structural steel members.
|
|
|
|
